last weekend's progress

The engine is nearly stripped to the short block. I managed to pull most of the vacuum hose rats nest off in one piece, as well as get the wiring loom off. I'm going to be going through the loom wire by wire before it goes back in - preventative on checking the wires, plus re-wrapping most of it. The protective wrapper of most of the loom is pretty crispy at this point. Not quite sure what the best option will be for re-wrapping. Does heat-shrink get brittle if exposed to continued heat?

I still have a few parts left that I can pull off - water pump, clutch, etc, but after that I'll be waiting on a bigger impact wrench to get the flywheel nut loose.

I can't believe how many places the block managed to leak either oil, water, fuel, or some horrible mix. I don't think it's a good sign that the exhaust ports of both rotors leaked a LOT of antifreeze.

M12 1.5 x70mm is harder to find that you'd think...

I thought I remembered autozone had a fair selection of metric hardware, so I stopped to try to find the bolts I needed to mount the engine to the stand I'm borrowing. Unfortunately they didn't have anything even close to what I needed.

Packed Riley up a little later in the weekend for a trip to Mclendon's, thinking a hardware store might have a better selection of metric bolts. I was able to find 2 m10 1.25 x70mm bolts, that will work for the upper mounts (where the power steering pump bracket bolts to the front housing). Still no bottom bolts. The person that helped at Mclendons suggested trying Tacoma Screw, but that Tacoma Screw is only open 7-5 m-f. Thankfully since daycare was closed for President's Day, I was working from home with Riley on Monday, and was able to run down and pick up the bolts before I started work for the day.

Monday evening, I sorted out a bracket solution that will work to mount a rotary to a generic engine stand, and got the engine mounted and off the hoist.

The engine is finally out! I haven't been able to mount it to the stand yet, will need a few longer metric bolts to connect to Ron's stand, but engine is out, and transmission is off. Forgot just what it takes to pop the clutch release, but once I figured out the right order, it came off nice and easy. Probably not a good sign when there's rust forming on the pressure plate though.

Last weekend of January, engine's still in the car

Guess at this point I'm a couple weeks behind schedule, not that I really have much of a deadline set. Starting to get nervous about what this is going to end up costing when it's all said and done.

I've joked in the past about how that car seems as if the transmission was placed on a pedestal, then the rest of the car was built around it. I was reminded of that thought this weekend. I've decided to pull the engine and transmission together (good thing, since I found a small oil leak coming from the transmission) which means un-bolting the PPF. In order to remove the PPF, I had to remove 3 belly trays and 2 braces, plus remove the 4 very tightly torqued nuts. I broke a socket adapter in the first attempt, so after a run to sears for a impact deep socket (something I should have anyway, it's the same size as the lugnuts on all three cars) and a replacement for the adapter it was back home thinking I was done on the car for the night.

While I was cooking dinner, I had a thought of a workaround on my air gun problems (far too many quick connect options, and I'm still not fully set after 2 trips to sears) that after dinner I went out to try. The workaround seemed to be good, so I thought I would just give it a quick test, then go back in for the evening. The quick test worked so well, I found myself sucked back in, and it wasn't until a half hour later when Carissa came out to see what I was doing that I realized I'd been reabsorbed in working. On the plus side, the PPF is off the transmission, the fuel lines are disconnected, clutch hydraulics are off, and I just have to pull the starter wiring as the last piece connecting engine to body.

Guess it's time to line up another pair of hands to help out next weekend!